Fifth Wheel Rails For RBW Lil Rocker Fifth Wheel Hitch

Question

Question:

Will these rails fit to a RBW Lil Rocker? Thank you

asked by: Dustin F

0

Expert Reply:

yes, the Curt Custom Fifth Wheel Installation Kit part # C16420-104 are industry standard rails which is what the RBW Lil Rocker needs to fit. You will not have any issues using the RBW Lil Rocker on these rails. They are designed for a 2003 to 2012 Dodge Ram and Ram 1500, 2500, and 3500 series trucks with either the 6' bed or the 8' bed.

expert reply by: Heather A

0

Answer 1

If your RBW Lil Rocker has ISR spacing (22" front to back from center of the feet) then you can use the Curt Custom Fifth Wheel Installation Kit for Chevy/GMC #C16418-204. If not then you would need to reach out to the manufacturer of the hitch…

view full answer...

Answer 2

The B&W Patriot 5th Wheel Trailer Hitch w/ Dual Jaws at 18,000 lbs. #BWRVK3255, is a great choice. Assuming that your current hitch is mounted to industry-standard, above-bed base rails, this will attach right to your existing rails without…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Fifth Wheel Rails For RBW Lil Rocker Fifth Wheel Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching