What is the Difference in the BB60010 and the BB60002

Question

Question:

What is the difference between the kit BB 60002 and BB 60010 for seal kits i have l68149 inner bearings

asked by: Richard M

1

Helpful Expert Reply:

The Spindle Grease Seal Set for L68149 Inner Bearing and 1.810 Bearing Buddy part # BB60010 has a seal outer diameter of 2.360" while the Spindle Grease Seal Set for LM48548 or L68149 Inner Bearing and 1.980, 1.968 or 2.562 Bearing Buddy part # BB60002 has a seal outer diameter of 2.560".

To determine your needs measure the back side of your hub where the grease seal presses in and go with the set that matches your hub.

expert reply by: Randy B

1

Answer 1

For the 1.06 inch diameter Timken bearing you would want the part #TM23VR and for the 1.375 inch you'd want the #TMK73VR.

view full answer...

Answer 2

According to the part numbers you gave it looks like you need outer bearing #L44649 with the matching race #L44610, inner bearing #L68149 with the matching race #L68111, and then the grease seal #168233 which has an inner diameter of 1.688" and…

view full answer...

Answer 3

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 4

After running the numbers the Seal Set #BB60010 you were looking at is for the L68149 Inner Bearing or the 1.810 Bearing Buddy. I don't think that is what you're looking for. I found this Seal Set #BB60002 which is for LM48548 or L68149 Inner…

view full answer...

Answer 5

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 6

We offer a range of grease seals in various sizes. These can be seen on the link provided. You can select parts based on the seal inner and outer diameters or you can use the bearing number from your trailer to search for a grease seal. I have…

view full answer...

Answer 7

You are correct, when replacing the hub/drum on your trailer you will only need to match the spindle to the inner diameter (I.D) of the bearings. The outer diameter (O.D) of the bearings would obviously have to match the hub but if you purchase them…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

What is the Difference in the BB60010 and the BB60002

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching