Measurement of Curt Front Mount Trailer Hitch # C31063

Question

Question:

I m about to purchase front hitch PN C31063 for 2000 ranger. Can you possibly email me a top view dimension drawing Thank You

asked by: Jim O

0

Expert Reply:

I was able to get some dimensions for you on the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # C31063. The overall width is 31-1/8 inches. The mounting holes are 29 inches by 10 inches on center. The receiver tube is 8 inches total front to back. I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

I definitely have the installation instructions for the Curt Front Mount Hitch #C31063 for your 2006 Ford Ranger. I went ahead and attached the pages to this answer. I also confirmed with Curt that this hitch fits a 2006 Ford Ranger XLT 4x4. Toward…

view full answer...

Answer 2

Installation of Curt front mount trailer hitch #C31063 will actually require some trimming of front fascia on a 2008 Ford Ranger. I have linked the instructions for you that show where the trimming takes place. This means it will likely be up higher…

view full answer...

Answer 3

We have a front mount, 2 inch receiver that will fit your 1998 Mazda B-Series pickup truck. It is Curt hitch #C31063. The only exceptions are that it will not fit on models with a front cross-member or 2-wheel drive models that were built in Canada.

view full answer...

Answer 4

I spoke with my contact at Curt and he provided a picture to show what to look for when it comes to determining whether your 2000 Ford Ranger has the front crossmember. You will see his picture off to the right. If your Ranger DOES NOT have a…

view full answer...

Answer 5

There sure is! To order the replacement mounting hardware for the Curt Front Mount Trailer Hitch Receiver #C31063 you have you will need the Replacement Hardware Kit #RHK. You will need to select Curt from the drop down menu, and then enter 31063 as…

view full answer...

Answer 6

Our hitch installers often find that on even fairly new trucks the weld nuts in the frame can becomes rusted enough (or filled with salt or dirt) that the hitch installation hardware does not want to thread properly. It can be an even worse problem…

view full answer...

Answer 7

Sounds like you are referring to a trailer hitch. And no, not all vehicles come from the factory with trailer hitches installed so the one you are selling just may not have ever had one. To see what a trailer hitch looks like that would fit your…

view full answer...

Answer 8

According to our friends at Curt Manufacturing, Front Mounted Receiver Hitch, part #C31063 is a fit for your 2000 Ford Ranger 4X4. If the truck is equipped with a skid shield, it must be removed to install the hitch. It will NOT fit on models with a…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Measurement of Curt Front Mount Trailer Hitch # C31063

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching