How Does Happijac Camper Jack Attach to Camper

Question

Question:

How does this attach to the camper?

asked by: Alexander L

0

Expert Reply:

On the camper you'd have a set of the Happijac Z-brackets like part # LC182493 installed which is what the jacks like part # LC736514-4 attach to.

expert reply by: Jameson C

0

Answer 1

The HappiJac Electric Truck Camper Jack System #LC736515-ELKIT is the current replacement for the HappiJac 4800 series jacks. This is an upgrade as it includes the electric motor versus the HappiJac Manual Truck Camper Jack System #LC736515-4 which…

view full answer...

Answer 2

We do not carry the Reico-Titan products so my research was more limited but after doing some research I was able to locate the installation instructions for the Reico-Titan Jacks. They have brackets listed specifically for the "C" clamp…

view full answer...

Answer 3

A simple to use, manual truck camper jack setup, I recommend the HappiJac Manual Truck Camper Jack System #LC736515-4. This kit comes with 4 camper jacks capable of lifting 11,200-lbs, and can lift to a maximum height of 36-1/2". This kit does…

view full answer...

Answer 4

I was not seeing a way to replace the white wire you are refereeing too, so I reached out to the manufacturer regarding your issue. The manufacturer said that the only way to replace the white wire going into the motor head area would be to replace…

view full answer...

Answer 5

Yes, the Happijac Qwik-Load turnbuckles are very similar to the Torklift Turnbuckles like the #TLS9529-2-LK so they would work fine.

view full answer...

Answer 6

You're actually on the right track, here. The TorkLift Custom Frame Mounted Tie Downs #TLF2021 and #TLF2021A (aluminum) are a confirmed fit through TorkLift for the 2020 F-350 with the running boards that extend past the cab of the truck. Since…

view full answer...

Answer 7

The HappiJac Truck-Mounted Camper Tie-Downs #LC236326-205221 will be the correct tie-downs for your 2018 Ram 2500. I would also recommend the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182895. These turnbuckles…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

How Does Happijac Camper Jack Attach to Camper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching