Available Trailer Brake Assemblies Compatible With Lippert 122460 3500 LB Capacity Hub/Drum

Question

Question:

I need to order trailer brakes and drums just need to make sure Im getting the correct ones. Hub part is 122460 L hand break is part number 297956 I just need to know what is the correct right side break part number. Thanks

asked by: Kirby

1

Helpful Expert Reply:

The Lippert 122460 you referenced is a standard 10 x 2-1/4 inch brake hub for a 3500 axle. It has a 5 lug on 4-1/2 inc bolt circle and is compatible with a L44649 outer and L68149 inner wheel bearing and a 1.719 ID grease seal. We offer compatible hubs as part # AKHD-545-35-EZ-K.

We don't offer Lippert brake assemblies, but the etrailer brand brake assemblies you'd looked at, part # AKEBRK-35 include the left and right brake assemblies that would definitely be compatible with your existing brake drums, but I'd recommend going with self adjusting brake assemblies like part # AKEBRK-35-SA. You'd need to manually adjust them, or make a series of stops in a parking lot to get them to initially auto adjust, but after that they'd adjust themselves. Dexter also offers a compatible set, part # 23-468-469 which would also be compatible with your Lippert brake drums. Quality wise, I'd say the Dexter brand is a higher quality product, more on par with your existing Lippert Brake Assemblies.

expert reply by: Mike L

1

Answer 1

If you are looking for the fuses on your 2015 Chevrolet Silverado 1500 that are tied to your trailer wiring then those will be in the fuse box in the engine compartment. You can find this information as well as a list of what all the fuses are tied…

view full answer...

Answer 2

I have attached a photo for you below which shows how both a vehicle side and trailer side trailer connector is typically wired. I say typically because this is not always exact and so long as the trailer and vehicle side both match it will not…

view full answer...

Answer 3

In order to add electric brakes to a trailer you'll need to know the axle capacity and wheel bolt pattern. The axle capacity should be printed on a tag in the center of the beam. Once you have this you can use it to pick out the correct braking…

view full answer...

Answer 4

You will need several items to add electric brakes to your Carry-On Utility trailer. Starting with the trailer you will need a hub and drum that matches the bearings and seal on your trailer spindle and your wheel bolt pattern. The only way to be…

view full answer...

Answer 5

I checked with Lippert and could not find any information on NV304664. Do you know the capacity of the axle? If it is a 7,000 pound axle then the likely inner bearing is #25580 and the outer bearing is #14125A. If a 2-1/4 inch seal diameter is needed…

view full answer...

Answer 6

The towing capacity of a 2004 Honda Odyssey is 3,500 lbs. If you are on the original transmission of the vehicle and it's never been rebuilt you'd be asking for trouble towing with your vehicle but a transmission cooler like the #D13502 would…

view full answer...

Answer 7

Since the load you will be towing is nearing the top of your 2003 Honda Odyssey's towing capacity, I recommend using the Derale Series 8000 Plate-Fin Transmission Cooler Kit #D13503. This cooler measures 11 inches wide x 8-3/4 inches tall x 7/8…

view full answer...

Answer 8

Most states do allow you to tow a trailer behind a trailer as long as it does not exceed a certain overall length- I believe California has a limit of 65 feet total length of all 3 vehicles. You would need to consult with your State's laws and…

view full answer...

Answer 9

If you need to tow with the tailgate down so you can haul your ATV in the truck bed then the most common solution for this is to use an extended weight distribution shank, the Equal-i-zer Weight Dist Shank part #EQ90-02-4600. This should provide…

view full answer...

Answer 10

A chrome finish ball #C40036 is going to look good but it will not be corrosion resistant. A ball with a machine finish like #C40087 , is going to have about the same corrosion resistance. In terms of performance they will wear at about the same rate…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Available Trailer Brake Assemblies Compatible With Lippert 122460 3500 LB Capacity Hub/Drum

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching