What is the Bracket Height and How Much Travel is Allowed with 60" Kwikee SuperSlide II

Question

Question:

What will be the full exstension on the 60 inch . And the total height of the rails

asked by: Richard S

0

Expert Reply:

The Kwikee SuperSlide II Tray Assembly Kit for RV Cargo Compartment - 60" Deep # LC370787 brackets are 4.67" tall and this assembly will allow the tray to extend out 42.42", so some of the tray you construct will be left supported on the brackets. You will also need a trim kit for the tray to complete installation and you'll want to choose the one that best suits your need by determining how wide your cargo compartment is. I've linked all of the available trim kits for you to choose from to this answer so that you can easily locate them.

expert reply by: Erik B

0

Answer 1

I reached out to Lippert to confirm and the Kwikee SuperSlide Tray Assembly with Trim Kit for RV Cargo Compartment part #LC370769 is adjustable as far as width goes. It is up to you to choose how wide you want the tray to be. Some will choose to have…

view full answer...

Answer 2

I have a suggestion for you, but unfortunately, we're not going to have a hitch mounted bike rack for electric bikes that's going to fit into your budget. Most of our e-bike racks max out at 60 lbs per bike, so your least expensive options…

view full answer...

Answer 3

The MORryde Sliding Tray #MR49 will clear a lip height of 1-5/8 inches but if you have the need for a higher clearance we have the: MORryde Sliding Tray Height Adjustment Kit #MR34VR. This raises the tray 2-1/2", 2-13/16", or 3-1/8".

view full answer...

Answer 4

The Air Lift LoadLifter 5000 Air Helper Springs #AL57365 will not raise the height of your 2010-2018 Ram 1500 because you will never be inflating them fully with no weight in the rear of your truck. Essentially, that wouldn't be a height that…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 10

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...