2019 Honda Passport Trailer Hitch Compatibility with Hands Free Lift Gate

Question

Question:

Do u sell a hitch to fit a 2019 Honda passport that does not interfere with the hands free lift gate?

asked by: Thomas

0

Expert Reply:

Both the Draw-Tite # 76290 and the Curt # C13421 are confirmed to fit your 2019 Honda Passport. They both state that the hands free sensors may be obstructed and function will be limited or possibly even lost. We haven't yet installed that hitch on your model year so we don't have the ability to give any further information on that. Sometimes sensors can be adjusted or repositioned to allow function of the hands free lift gate so I personally wouldn't hesitate but it may take a little work around to get the functions to work.

expert reply by: Jason S

0

Answer 1

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

We haven't yet had the chance to install either the Draw-Tite #76290 or the Curt #C13421 on a 2019 Honda Passport, so those measurements aren't available to me, unfortunately. That being said, based on the photos I attached comparing the two,…

view full answer...

Answer 4

The best hitch for your 2023 Honda Passport is going to be the Curt Hitch item #C13421. This hitch is custom fit and bolts to your Honda with included hardware. I really like the Curt hitch because it tucks up underneath your rear bumper cover nicely…

view full answer...

Answer 5

The Curt hitch part #C13421 that fits your 2019 Honda Passport will not interfere with the hands-free liftgate feature. You will likely have to kick your foot to one side of the receiver as opposed to the middle but that would be it.

view full answer...

Answer 6

I have attached a photo of the Curt Trailer Hitch Receiver part #C13421 installed on a 2019 Honda Passport. As you can see, the receiver tube is tucked neatly under the rear bumper but it does not install behind the rear bumper panel nor do any of…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...