Mounting Hole Spacing for the Optronics LED Trailer License Plate Light

Question

Question:

Your info says 3-1/4 inch mount hole spacing and 3-1/2 inch spacing. Which is it. I need 3-1/2. Thanks,

asked by: Fred F

1

Helpful Expert Reply:

The two mounting holes on the Optronics LED Trailer License Plate Light part # LPL56CB which attach the bracket to the trailer are spaced apart 3-1/2" on center so it will be a direct fit for you.

expert reply by: Conner L

1

click to enlarge

Answer 1

The Optronics LED Trailer License Plate Light with Bracket - Submersible #LPL56CB is submersible and will work with your trailer. On The LED Trailer License Plate Light with Mounting Bracket #328-003-70BE if the lights are submerged they will stop…

view full answer...

Answer 2

Often the license plate holder has an integrated light that requires replacing the entire holder as well. I recommend the LED Trailer License-Plate Light w/ Mounting Bracket - 2 Wire - 5 Diodes - Clear #LPL56CB because there are no bulbs to replace…

view full answer...

Answer 3

To use the Thule License Plate Holder #TH35JV with the Thule EasyFold XT Bike Rack #TH903202 you will need to attach it to one of your bikes as the holder is designed to attach to either a vertical or horizontal bar. Since the Thule EasyFold XT…

view full answer...

Answer 4

Past customers have told us the AL-KO 8460 uses inner bearing 25580 and outer bearing 15123, which would make the Timken Bearing Kit #TMK82VR the correct replacement bearing kit for that hub. If you are looking to replace the hub entirely the…

view full answer...

Answer 5

Yes, it does. The Hollywood Racks LED Light Bar item #HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights.

view full answer...

Answer 6

I think the best option we have for you is a universal weld-on hitch plate like one of the following that I have attached for you. We do not really have any direct fit hitch plates for you so I think this will be the best option we can offer. If you…

view full answer...

Answer 7

The mounting holes on the Buyers Products 50 Ton Air Compensated Pintle Hook #337PH50AC are 0.781" in diameter. The horizontal mounting holes are 5" apart center on center, and the vertical mounting holes are 2.375" at the top and…

view full answer...

Answer 8

What you're looking for is the Replacement Spring Bars for Blue Ox 2-Point Weight Distribution System #BLU64XR. These spring bars will work with any Blue Ox 2 point WDS and have the same 800 - 1,200 lb tongue weight rating you mention.

view full answer...

Answer 9

For your application I recommend the Light Kit #20174 and 2 of the Mounting Bracket #BK70BB. These will mount under the horizontal bars for the Hollywood Racks Sport Rider SE #HLY84FR. When it comes to the license plate bracket I'm not quite sure…

view full answer...

Answer 10

Hello again Michelle. The Saris Glide EX Bike Rack #SA774 will indeed fit a 2023 Hyundai Tucson with a class 3 hitch. The tilt feature will allow the hitch to open and close normally. Saris bike racks are definitely good quality. They are all made…

view full answer...

Answer 11

We have the perfect replacement Lid Support For your Older Yakima Rocket Box! The Replacement Lid Support for Yakima Cargo Boxes #8880683 will replace the front and rear of the RocketBox (8007147, Y07191, and Y07192).

view full answer...

Mounting Hole Spacing for the Optronics LED Trailer License Plate Light

Product Page this Question was Asked From

Continue Researching