Compatibility of 3430001 Autowbrake Brake Controller with 2012 Volvo C70

Question

Question:

I Had a 7 pin plug put on my Volvo C 70 at the Uhaul place along with a class 1 hitch. I will be towing a 1200 pound Nucamp Boondock lite, that weights about 1200 pounds and has electric brakes. Will this AUTOWBRAKE unit work on this vehicle without drawing too much amperage through the 7 pin plug?

asked by: David

0

Expert Reply:

As long as the 7-way was installed correctly with a circuit breaker protected connection to the tow vehicle battery, the # 3430001 Autowbrake Brake Controller you mentioned will work just fine. A single axle trailer will only draw about 6 amps at full braking power, so there will be no problems at all as the power circuit through the 7-way is usually protected by a 30 amp breaker or fuse at a minimum.

If you click the provided link you can see a product video featuing the Autowbrake # 3430001.

expert reply by: Mike L

0

David

4/11/2020

The 7 blade trailer plug on my Volvo C 70 is connected to the battery directly with a 15 amp fuse. Will this be sufficient for the AUTOWBRAKE?

Reply

Chris R.

4/13/2020

Yes, the battery connection and 15 amp fuse/breaker that you have installed in-line will work just fine.

Reply

Answer 1

The Autowbrake brake controller part #3430001 that you referenced draws up to 15 amps. It's only going to draw amperage when the controller is activating the trailer brake so it would not be something you'd need to install an on/off switch on…

view full answer...

Answer 2

For the most reliable and safe connection possible, Curt recommends obtaining the power for the controller directly from the vehicle battery and running the circuit through a 30 amp breaker like what's provided with the #ETBC7. This way, you can…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...