Can 2019 Mitsubishi Outlander Sport be Towed Behind Motorhome

Question

Question:

Will this fit my vehicle? They haven’t changed much since 2015 model and I can’t find it for my model year

asked by: Edgar

0

Expert Reply:

I checked with our base plate manufacturers and they don't have a fit for your 2019 Mitsubishi Outlander Sport but I also did some digging and it looks like your vehicle can only be flat towed on a tow dolly so that is most likely why a fit was never released. So your best option would be a tow dolly like the Roadmaster # RM-2050-1 to tow your Outlander around as needed.

expert reply by: Jameson C

0

Answer 1

They are not flat towable. They have the CVT which makes them incompatible. The Outlander Sport with the manual transmission with FWD can use a tow dolly like the Roadmaster Tow Dolly with Electric Brakes - 4,250 lbs #RM-2050-1 for electric brakes or…

view full answer...

Answer 2

The Roadmaster Tow Dolly #RM-2050-1 will definitely be the suggestion I would make. That being said, this is specifically for the front wheel drive models. If you have an all wheel drive model however, you will have to have all 4 wheels off the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...