Replacemet Wheel Bearings for 2020 No Boundaries 19.5 with 4,400 lb Lippert Torsion Axle

Question

Question:

Would like to have a spare set of wheel bearings on hand for excursion travel - its one of those not easily found in Northwest Territories. The info on the axle of my No Boundaries 19.5 is a s follows 4400 LB axle ID# 774025 Ser # S003959875 Mfg Date 09-10-19 Part # LCI35H-DTBSA-79.5-59.25-ID-22D-LPIB-L-655-18PT-CAP4400

asked by: Cath E

0

Expert Reply:

The correct bearing kit for your 4,400 lb Lippert Torsion Axle is part # BK2-100. I confirmed this information through my contact at Lippert based on the serial number S003959875.

This bearing kit includes one outer bearing # L44649 with matching race, one inner bearing # L68149 with matching race, one 10-19 double lip grease seal # 58846 and a cotter pin for standard spindles as well as a tang washer for EZ-Lube spindles.

For the replacement grease caps, you can use part # RG04-040. It would also be a good idea to keep some bearing grease on hand. For that I recommend using LMX Red Grease # L11390, which can be applied with a grease gun like # PTW54290.

expert reply by: Carla M

0

Answer 1

We do have the bearings you need for your Lippert 4,400 lb trailer axle: - Inner bearing #L68149 - Outer bearing #L44649 You can also get the bearings, races and seal with one kit, the Bearing Kit #BK2-100. If you are looking for grease as well, I…

view full answer...

Answer 2

The 12V power circuit in an aftermarket 7-way connector like #37185 will usually be connected to the vehicle battery through a 40-amp circuit breaker like #PK54540. This installation provides for 12V power at the connector contact at all times, even…

view full answer...

Answer 3

I took a look at the parts you mentioned and they were only specified as a "dust cap for a 2.5" bore." For that you can use the 2-1/2" Lubed Dust Cap and Rubber Plug #DC250L-DCRP which measures 2.45" x 1.52" x…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 7

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 11

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 12

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Replacemet Wheel Bearings for 2020 No Boundaries 19.5 with 4,400 lb Lippert Torsion Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching