Does the Replacement Bolts for Fastway e2 Weight Distribution Head Comes With Conical Tooth Washers

Question

Question:

Does the kit FA92-02-9600 come with flat washers or conical toothed washers? Hard to tell with the picture?

asked by: Chris

0

Expert Reply:

The Replacement Bolts for Fastway e2 Weight Distribution Head part # FA92-02-9600 come with the following:

(2) 3/4-10 x 5" grade five bolts
(4) 3/4 conical-toothed washers
(1) hitch pin
(1) hitch pin clip,
(1) spacer rivet
(7) spacer washers
(2) 3/4" nylock nut.

expert reply by: Conner L

0

Answer 1

I would recommend using the exact procedure you outlined. Tighten the shank bolts first and then with the shank in the vehicle hitch (secured with hitch pin) torque down the hitch ball to 450 ft lbs.

view full answer...

Answer 2

In order to choose the correct weight distribution system for your needs, you'll need to find the tongue weight of your trailer when it's fully loaded and ready to tow. A tongue weight scale like #e99044 is a handy item to have to determine…

view full answer...

Answer 3

You should add one spacer washer at a time with the Fastway e2 Weight Distribution System #FA92-00-1000 as there is not a specific formula regarding one washer equaling a certain measurement. The reason for this is that there are too many variables…

view full answer...

Answer 4

According to Fastway it is 1-3/8" square opening on Replacement Trunnion #FA92-02-1044. I was also informed that they do use different size bars on their different weight ratings so if you are unsure of your weight rating of your bars, please…

view full answer...

Answer 5

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 6

When setting up your Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0800 both the tow vehicle and trailer should be loaded just like they would be when you're traveling. This is can be found in the installation instructions under…

view full answer...

Answer 7

Typically what people do to mount the propane tank covers like the part #CAM40542 is to use a bungee cord like #EM06755 to secure it below the tanks. The cover has two tabs on the bottom of it that allow for the hooks of the strap to be attached to…

view full answer...

Answer 8

When it comes to getting replacement spacer rivets and washers for your Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 8,000 pounds GTW, 800 pounds TW #FA92-00-0800 you will need The Replacement Hardware Kit for Fastway e2 Weight…

view full answer...

Answer 9

The head unit you inquired about, the Replacement Head for Fastway e2 Weight Distribution Systems #FA92-02-1255, is the correct replacement head unit for the Trunnion Bar systems that are rated for 6,000 lbs, 8,000 lbs, 10,0000 lbs, or 12,000 lbs.…

view full answer...

Answer 10

The Replacement Head for Fastway e2 Weight Distribution Systems - Round Bar, part #FA94-02-1055 weighs approximately 16-17 lbs.

view full answer...

Answer 11

Since the same head unit #FA94-02-1055 is used for your current 8K system #FA94-00-0800 and the 10K system #FA94-00-1061, you can certainly upgrade your bars to the 1,000 lb TW part #FA94-02-1099 for your new trailer. Just be sure to check your…

view full answer...

Answer 12

Yes, the best way to deter thieves with bolt cutters is to use a very short pin lock in the latch part #e98885. This etrailer.com stainless steel coupler lock only measures a 1/2" span and will not give the thief room to use the bolt cutters to…

view full answer...

Does the Replacement Bolts for Fastway e2 Weight Distribution Head Comes With Conical Tooth Washers

Product Page this Question was Asked From

Continue Researching