What Keeps Propane Tank Cover CAM40542 Secured to Propane Tanks

Question

Question:

What makes this cover not blow off during traveling if it is not secured in some manner?

asked by: Sharon V

0

Expert Reply:

Typically what people do to mount the propane tank covers like the part # CAM40542 is to use a bungee cord like # EM06755 to secure it below the tanks. The cover has two tabs on the bottom of it that allow for the hooks of the strap to be attached to so that you can secure it.

expert reply by: Jameson C

0

Answer 1

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according…

view full answer...

Answer 2

Correct, the Dexter E-Z Flex Suspension Kit part #K71-653-00 is what you would want to use to upgrade the equalizers on your trailer. The total difference in length will only be around 1/2" between the equalizers and shackle straps but since…

view full answer...

Answer 3

Dexter components like the Dexter E-Z Flex Equalizers #K71-655-00 you were looking at will work just fine on your Lippert axle, but you will want to make sure that the new equalizer has the same horizontal bolt hole distance as your current…

view full answer...

Answer 4

The correct MORryde Shock Absorbing Suspension Equalizers for a 2022 Grand Design Imagine XLS 22RBE is part #MR27ZR. The correct MORryde Suspension Upgrade Kit is part #MR46ZR. These are both great options to upgrade your suspension allowing for a…

view full answer...

Answer 5

We offer Class V hitches in both 2-inch and 2-1/2-inch sizes for your 2009 Chevrolet Silverado 2500. All are shown on the linked page. Draw-Tite's 2-inch hitch #41944 is a no-drill install since it bolts up to the bumper bracket the same way as…

view full answer...

Answer 6

For your 2005 Chevy Silverado I would recommend the Draw Tite Hitch part #41944. This hitch requires no drilling for installation, has a 13k capacity and will replace your current factory hitch. I attached an install video for you to check out as…

view full answer...

Answer 7

When setting up your Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0800 both the tow vehicle and trailer should be loaded just like they would be when you're traveling. This is can be found in the installation instructions under…

view full answer...

Answer 8

The Replacement Head for Fastway e2 Weight Distribution Systems - Round Bar, part #FA94-02-1055 weighs approximately 16-17 lbs.

view full answer...

Answer 9

The head unit you inquired about, the Replacement Head for Fastway e2 Weight Distribution Systems #FA92-02-1255, is the correct replacement head unit for the Trunnion Bar systems that are rated for 6,000 lbs, 8,000 lbs, 10,0000 lbs, or 12,000 lbs.…

view full answer...

Answer 10

Since the same head unit #FA94-02-1055 is used for your current 8K system #FA94-00-0800 and the 10K system #FA94-00-1061, you can certainly upgrade your bars to the 1,000 lb TW part #FA94-02-1099 for your new trailer. Just be sure to check your…

view full answer...

Answer 11

To upgrade your Fastway E2 weight distribution system #FA92-00-0800 to be rated for 1,200 lbs of tongue weight you could replace the spring bars of the system with the part #FA92-01-1099 that are rated for 1,200 lbs of tongue weight.

view full answer...

Answer 12

When installing a Slide-Topper on your trailer, you will just want the awning rail to be a couple inches above the top flange on the slide-out. This is simply to provide a slight downward angle for rain runoff. There shouldn't be any issue with…

view full answer...

What Keeps Propane Tank Cover CAM40542 Secured to Propane Tanks

Products Referenced in This Question

Continue Researching