Global Links RV Door Lock Numbers 391 and 379

Question

Question:

Are these keys pre-cut, or do I have to take to locksmith to get cut?

asked by: Corky F

1

Helpful Expert Reply:

The Replacement Global Link RV lock keys like part # 295-000158 that you referenced are pre-cut. You would not have to have them cut. This is correct replacement key for number 379. For key number 391 you'd want # 295-000079.

expert reply by: Jameson C

1

Answer 1

The first thing I would do is check the brake output circuit on the 7-way of your tow vehicle. You will want to use a circuit tester like our part #3808 to check for voltage at this circuit when the manual override of your brake controller is…

view full answer...

Answer 2

Testing lights on your trailer will require a 12V power source so if you are not going to plug in a connector like #H20046 you will need a separate 12V battery. Then use the negative post of the battery to attach your ground wire to and then and use…

view full answer...

Answer 3

The 5-way flat trailer connector in-line circuit tester #20115 you referenced won't be needed. You would need to have a 12V power source and your jumper wire which will let you know if you have working trailer lights. The most common gauge…

view full answer...

Answer 4

The replacement lock you need is the Global Link RV Baggage Door Slam Latch #295-000078. This lock fits with the Key for Global Link RV Standard Baggage Door Locks #295-000079 (which is key G391).

view full answer...

Answer 5

For your 2019 Ford F-250 there are two RoadActive Suspension kits for your truck available. There's the part #RAS3611-SLHD which is intended for versions of the vehicle that do come with overload springs and there's the #RAS3611-S which does…

view full answer...

Answer 6

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 7

The lock code could be located on the key itself, on the face of the lock core, or one a sticker attached to the lock (see photos). Once you find this you can then order the correct replacement key assuming you have a Global Link, Fastec (FIC),…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Global Links RV Door Lock Numbers 391 and 379

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching