What Size Threads Does the Replacement Hitch Cup Assembly for Ultra-Fab Tripod Use

Question

Question:

Will this cup fit my eaz lift gooseneck stabilizer model #48850

asked by: Willard D

0

Expert Reply:

The Replacement Hitch Cup Assembly for Ultra-Fab 5th Wheel King Pin Tripod Stabilizers part # UF19-001056 is a direct replacement for the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part # UF19-950001. In order to use the cup with another stabilizer you would need to ensure it accepts 1-1/4"-10 threads. If not, you would need to replace the stabilizer altogether.

The EZ-Lift Gooseneck Stabilizer is not a product we carry so I cannot confirm fit.

expert reply by: Conner L

0

Answer 1

Yes, the Hitch Cup Assembly #UF19-001056 can be used in place of the Ball Assembly #UF19-001057 on the Ultra-Fab Gooseneck Trailer Tripod Stabilizer #UF19-950450. This will effectively give you the 5th Wheel King Pin Tripod Stabilizer #UF19-950500.

view full answer...

Answer 2

The Replacement Hitch Cup Assembly for Ultra-Fab 5th Wheel King Pin Tripod Stabilizers part #UF19-001056 is made of aluminum. I called my contact Ultra-Fab to confirm this. This cup is used on both the Ultra-Fab 5th Wheel King Pin Tripod Stabilizers…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

What Size Threads Does the Replacement Hitch Cup Assembly for Ultra-Fab Tripod Use

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching