Bunk Board Carpet for a Pair of 6 Foot 2 x 4 Bunk Boards

Question

Question:

Hello, Will one 11x12 roll of carpet cover 2- 2x4x6 boards? or do I need extra for the ends?

asked by: Lorrin R

0

Expert Reply:

You can use one roll of 12 foot long x 11 inch wide bunk carpeting for a pair of 6 foot 2x4 bunk boards. Just be sure to be measure twice and cut once, as they say, and you'll be fine! With the length set, all you need to do is choose the color you want, with the options linked below.

- Black: CE Smith Deluxe Marine-Grade Carpeting for Bunk Boards # CE11330
- Charcoal: CE Smith Deluxe Marine-Grade Carpeting for Bunk Boards # CE11372
- Blue: CE Smith Deluxe Marine-Grade Carpeting for Bunk Boards # CE11350

I have added links to a couple video reviews for you to check out as well.

expert reply by: Kyle S

0

Answer 1

We most likely do, however, we don't have a list of bearings for each trailer. You will need to pull one of your hubs and then remove the inner and outer bearing and look at the face of each one. There should be a number stamped into the face of…

view full answer...

Answer 2

The extra loop is referred to as a hand saver loop. It simply provides a safer place to grab the end of the strap for when you're pulling out slack from the winch drum. The snap hooks can get torn up a little, and could be rough on your fingers…

view full answer...

Answer 3

We typically try to use 1/2 inch stainless steel staples when we install the CE Smith Deluxe Marine-Grade Carpeting, #CE11372, but 3/8 inch staples will work too. I would not go much shorter than the 3/8 inch staples because you don't want them…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...