Is the LubriMatic Marine Trailer Bearing Grease Compatible with Starplex EP 2 Grease

Question

Question:

My Karavan boat trailer bearings came factory packed with Texaco/Chevron Starplex EP2. Is this product compatabile?

asked by: Jeff A

0

Expert Reply:

Yes, the LubriMatic Marine Trailer Bearing Grease, # L54FR, is compatible with the Starplex EP 2 grease that you currently have on your Karavan boat trailer.

I have attached an article on lubricating grease that you may find helpful when searching for new bearing grease.

expert reply by: John H

0

Answer 1

The two maximum load ratings listed for the Westlake ST235/85R16 Radial Trailer Tire #LHWL410 refer to single rear wheels or dually wheels on a trailer. The dual tire rating of 3,860 pounds at 110 psi refers to having two tires on each side of a…

view full answer...

Answer 2

In order to choose the correct replacement axle for a trailer you'll first want to start with the weight capacity. The weight capacity can be found on the axle tag in the center of the beam. Then, you'll need to measure the hub face (center…

view full answer...

Answer 3

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 4

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Is the LubriMatic Marine Trailer Bearing Grease Compatible with Starplex EP 2 Grease

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching