SumoSprings and Rear Sway Bar Recommendation 2018 Jayco Melbourne on Mercedes 3500 Chassis

Question

Question:

2018 Melbourne on a 2017 Mercedes 3500 chassis

asked by: Michael T

0

Expert Reply:

Can you get me the year of your Melbourne? With that I'll be able to pick you out the correct parts that would fit. Thanks!
Jameson

expert reply by: Jameson C

0

Michael T.

3/11/2020

2018 Melbourne on a 2017 Mercedes 3500 chassis

Reply

Jameson C.

3/11/2020

Thanks! So the correct rear sway bar is the part # RM-1209-131 which I attached an install video for. This will make the biggest improvement. Then for SumoSprings the # SSR-339-40-2 will give you the best support and ride quality for the rear suspension and you'd be set!

Reply

Answer 1

As long as the Roadmaster rear sway bar part #RM-1209-131 was installed properly it would not void the chassis warranty of your 2018 Mercedes Benz Sprinter Chassis because of the Magnuson Moss act. The Magnuson–Moss Warranty Act in short states that…

view full answer...

Answer 2

We do not have an option for front anti-sway bar on the 2018 Mercedes Benz Sprinter 3500. However, there are two options for the rear, the Roadmaster Rear Anti-Sway Bar, #RM-1209-120 is a factory sway bar replacement that is 1-3/8 inch diameter. The…

view full answer...

Answer 3

The amount of times you'd need to wind a Solera awning when installing it is 14 times. The part number you have 285148 matches up with the #LC87FR.

view full answer...

Answer 4

I have a solution for you, but my contact over at Lippert tells me that you won't be able to replace just those casings on Solera Slide-Out Topper. The parts you need are the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning -…

view full answer...

Answer 5

You do not have to remove the entire slide topper to be able to replace the Idler Head and Roll Tube #LC87FR for your Solera slide topper. A second person will be able to support the weight of the tube and fabric in place while the assembly is…

view full answer...

Answer 6

The only way to get the Solera part you are looking for is to order the part number #LC87FR that you referenced as Solera does not offer it separately.

view full answer...

Answer 7

You are looking for the #LC34FR, which is the replacement Drive Head for a Solera Slide-Out Awning. This will replace your broken driver head and slide into the fabric roller. The Idler Head is available with #LC87FR if you find that also is…

view full answer...

Answer 8

There isn't a left or right hand version of the Replacement Idler Head and Roll Tube part #LC87FR that you referenced.

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

SumoSprings and Rear Sway Bar Recommendation 2018 Jayco Melbourne on Mercedes 3500 Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching