Master Cylinder Assembly for Titan Model 60 Brake Actuator

Question

Question:

I was about to order the item #4395100 and the push rod. I have a Trailex Aluminum car dolly with drum brakes and not made anymore. But it has a model 60 hitch with a Dico 189 master cylinder. All looks well except the height yours says 3 5/8 inch? mine is 3 tall which just fits, X 2 1/8 wide . Am I looking at the wrong one? Or maybe I am stuck. Bolts are 1/4 inch and 2 1/2 x 3 1/2 apart which could be re-drilled.

asked by: Jerald G

0

Expert Reply:

I can tell you for sure that the correct replacement master cylinder assembly for a Model 60 (either Titan or Dico) brake actuator hitch is the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum # T4395100.

I researched and was unable to find a reference to a Dico 189 cylinder, but if you have a Model 60, you've found the right master cylinder. It sounds like you indeed will have to re-drill the bolt holes to install this replacement.

expert reply by: Kyle S

0

Answer 1

Based on the link you asked the question from, I assume you have hydraulic brakes on your trailer. The first thing I would check is the break away cable and assembly to see if it is engaged or partially engaged. If that isn't the issue, I'd…

view full answer...

Answer 2

It doesn't matter which wire is grounded and which get run to the reverse light circuit of the 7-way on your trailer. I attached an FAQ on trailer wiring for you to check out also.

view full answer...

Answer 3

The correct replacement master cylinder for your Titan Model 60 Disc Actuator is part #T4820000. This kit includes the following components: ?Master cylinder ?Gasket ?Orifice connector ?Hex bolt: 3/4" long x 1/4" diameter ?Lock washer:…

view full answer...

Answer 4

The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…

view full answer...

Answer 5

I've looked through the various replacement master cylinders we offer, and couldn't find anything that matches your photo. I found out that Reliable stopped manufacturing brake actuators several years ago, and replacement parts aren't…

view full answer...

Answer 6

I would love to sell you a complete system but I think that it may be simpler to take care of the problem. Since you said you have taken the brakes apart and find no issues, the problem may be in the actuator. The master cylinder could be the…

view full answer...

Answer 7

Since your brakes aren't releasing, it sounds like you either have a bad master cylinder in your surge coupler or a bad shock. The caliper piston moved when you released the pressure with the bleed valve, so it appears the plunger on the master…

view full answer...

Answer 8

The Titan 60ZX7000 brake actuator is a Model 60 actuator, and you do have the correct part for a replacement master cylinder: - Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 So this will work…

view full answer...

Answer 9

The Titan Replacement Master Cylinder Assembly #T4395100 is a direct replacement for Model 60 and Aero 7500 drum brake actuators. I measured this item and put the dimensions on the included photo. Overall assembled height including the filler cap is…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Master Cylinder Assembly for Titan Model 60 Brake Actuator

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching