Will Lippert High-Speed Power Stabilizer Jack Fit 2015 Forest River Wildcat 5th Wheel Trailer

Question

Question:

The specs of LC337199 say 20 inches wide. I just took mine off and its 17 inches wide. All other specs are accurate. Do I have the correct replacement part?

asked by: Steve

0

Expert Reply:

Lippert has had some upgrades recently for the High-Speed power stabilizer jack so if your current one is from Lippert then the # LC298707 that you referenced is the correct replacement and will fit properly.

Attached is a sample installation video for you to check out.

expert reply by: Jon G

0

Steve K.

3/17/2020

I received the product today and its a match!! The productJack is 17 inches wide and not 20 inches per the specs. please add this note to if it doesnt do it automagically

Reply

Chris R.

3/18/2020

Thanks so much for the info! We really appreciate this kind of feedback. We will get that page updated shortly.

Reply

Answer 1

Typically around the motor area of the stabilizer jack there will be a label that will have part numbers and other info listed. I attached a picture of what it looks like on the #LC298707 that you referenced. Lippert does sometimes use alternate part…

view full answer...

Answer 2

You will want to use a minimum of 10 gauge wire like #10-1-1 from the battery to the motor on the Lippert High-Speed Power Stabilizer Jack #LC298707. I do not recommend running a front and rear stabilizer to the same power wire. Each wire uses a…

view full answer...

Answer 3

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 4

The circuit rating for the motor on the Lippert High-Speed Power Stabilizer Jack part #LC298707 is 20 amps so you'll need to use this along with the distance between the jack motor and battery to find the correct size wire. You can find charts…

view full answer...

Answer 5

Really you're going to need to measure the distance where the leveling system is going to be installed. If that distance is more than 20', then you're going to want the 6 point Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling…

view full answer...

Answer 6

I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the #LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam. If clearance…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 9

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 10

The 30" Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR have a weld on design. This is the only way to install the jacks with the included mounts as there is not enough room between the stabilizer itself and the mounting plate for additional…

view full answer...

Answer 11

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Will Lippert High-Speed Power Stabilizer Jack Fit 2015 Forest River Wildcat 5th Wheel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching