Picking Out Replacement Dexter Brake Assemblies for 2006 Peterson Excel 5th Wheel

Question

Question:

We have a 2006 Peterson Excel fifth wheel that needs new brake pads. It comes with Dexter axles. Will K71-629 fit ?

asked by: David

0

Expert Reply:

Depends on the capacity of the Dexter axles you have. If they are between 6k and 8k the # K71-629 is correct for Dexter calipers. If they were between 10 and 12k you'd instead want the # BP04-395. If you had 3,500 lb axles the part # K71-623-00 would be what you'd need.

expert reply by: Jameson C

0

Answer 1

As long as your existing hub drums are in good condition (no grooves worn in the armature surface that the brake magnet rides on or the surface that the pads grab). For a lot of trailer hub/drums there is a minimum thickness for that to be turned…

view full answer...

Answer 2

On many drum brakes there are wear indicators at the pad material on the shoes. If the pad material is riveted on and you have reached the rivets then it is time to replace them. If you have the brakes adjusted out all the way and the braking is…

view full answer...

Answer 3

There are a few differences between the Dexter 3,500 lb brake assemblies and the 4,400 lb brake assemblies including the brake shoes, magnets, adjusters and adjuster springs. Because the 4,400 lb brake assemblies must be able to provide more…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Picking Out Replacement Dexter Brake Assemblies for 2006 Peterson Excel 5th Wheel

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching