Lippert Rear Stabilizer Model 201353 Shear Pin Replacement

Question

Question:

My pin sheared on the stabilizer motor and I am wondering if I can order just a pin and what would be the model number or size I need?

asked by: Aaron

0

Expert Reply:

I contacted Lippert Components to ensure we get you the right pin and they said that there are two pins located right by each other there at the motor. These should both be replaced. The larger one Replacement 5/32" x 1" Roll Pin for Lippert Components Stabilizer Jacks part # LC125462 is the one slightly closer to the motor and the smaller Replacement 3/32" x 1" Roll Pin for Lippert Components Stabilizer Jacks part # LC181003 is located about an inch closer to the middle of the camper. Replace these and you will be back up and running, Happy Camping!

expert reply by: Randy B

0

Answer 1

Per the manufacturer when it comes to the shear pins being broken you would have to replace the whole Lippert Jack #LC298707 because the shear pins are not replaceable, and there is no way to fix them. What you will need to do is purchase a whole new…

view full answer...

Answer 2

I reached out to Lippert for help identifying the pin that you have missing but unfortunately they do not list this as a replacement part for your PSx2 Stabilizer jack. We do carry a 5/32" #LC125462 and 3/32" #LC181003 roll pin which was…

view full answer...

Answer 3

When your Lippert Ground Control 3.0 #LC358590 has a reading that says "Comm Error" it is referring to the communication between the controller and touch pad. You will need to check your harness to ensure it is connected properly and there…

view full answer...

Answer 4

I talked with my contact at Cequent and he stated that the life of a plastic lube plate can vary depending on several factors. Pin weight, the smoothness of the components touching the plate, and where you are towing (dirt, gravel, highway) are all…

view full answer...

Answer 5

Thanks for the photo, and I searched but could not find anything with the numbers on the sticker. Truly, the only way to know which is the correct replacement is to know the model of your Lippert stabilizer jack. There are only a couple that are…

view full answer...

Answer 6

The difference between the Optronics LED stop/turn/tail light #STL69RRXB and the Optronics LED stop/turn/tail light #STL69RB is #STL69RRXB will have an integrated red reflector to fulfill the rear reflex requirement. If you choose to go with…

view full answer...

Answer 7

The brake output circuit of your vehicle/trailer wiring wouldn't be an ideal circuit to power the third brake light of a trailer unless you wanted to modify the circuit on your tow vehicle. You would have to run a brake light circuit straight to…

view full answer...

Answer 8

The only difference between the two is the height of the lamp. The Optronics #STL69RRXB is 15 inches long by 1-5/8 inches tall, while the #STL69RB is 15 inches long by 1-3/8 inches tall, a 1/4 inch difference. Other than that, both lamps are pretty…

view full answer...

Answer 9

Red, black, and white wires are common on many tail light assemblies. When this is the case, you will have red as stop and turn, black as running light, and white as ground. So you will connect yellow to red on one side of the trailer and green to…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 12

Welcome back! We do not sell the breakers you'll need for the Progressive Dynamics 4100 Series RV Converter item #PD4135K you purchased but I have listed below the ones Progressive Dynamics recommends. You can source them at your local hardware…

view full answer...

Lippert Rear Stabilizer Model 201353 Shear Pin Replacement

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching