Scissor Step Stair Bracket Dimensions

Question

Question:

what is the overallwidth & length of the bracket. We have a camper with the septic attachment on the left of the door and under the door is a box that opens so im trying to see if this will work, with all of these in the way. thank you

asked by: Tracy

0

Expert Reply:

The AS24 mounting bracket is 25 inches long and 1-1/2 inches wide and should be placed 1/8 inch below the lowest part of the door on your RV.

expert reply by: Robert G

0

Answer 1

Sounds like you'd want to go with a removable scissor setup like the Brophy Camper Steps part #AS24 which will need to be taken off it's mounting bracket between uses. This will give you total access to your trailer hitch when…

view full answer...

Answer 2

The Brophy Camper Scissor Steps part #AS24 will require 1-1/4" of clearance between the bottom of the door and bottom of the cab on your Palomino Truck Bed Camper in order for the mounting bracket to attach. If you removed a portion of the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Are you basically asking how much length would this coupler add to the tongue of your trailer?

view full answer...

Answer 6

It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.

view full answer...

Answer 7

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Scissor Step Stair Bracket Dimensions

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching