Front Hitch Recommendation for 2020 Ford F-350

Question

Question:

Which front hitch should I get for my 2020 Ford F-350?

asked by: Sarah

0

Expert Reply:

For your 2020 Ford F-350 I recommend the Draw Tite hitch part # 65076 as it has plenty of weight capacity, installs easily, and has great ground clearance. Check out the install picture I attached.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It looks like the hitch pin hole on the Curt Front Mount Trailer Hitch Receiver #C31078 will stick behind and/or below the fascia while the Draw-Tite Front Mount Trailer Hitch Receiver #65076 will stick out far enough to easily reach the hitch pin…

view full answer...

Answer 2

Both of the front mounted hitches you referenced, Draw-Tite #65076 and Curt #C31078 are confirmed fits for all models of the 2017 Ford F-250 Super Duty. They will not interfere with your axles; you can check out how each looks in the photos I've…

view full answer...

Answer 3

The Curt 5th Wheel/Gooseneck Custom Wiring Harness #C57010 uses a 10' long harness. It will connect in line of your current 7-way in your bed allowing you to install another 7-way in the front of your bed on your 2019 Ford F-350. This will allow…

view full answer...

Answer 4

Unfortunately no, the Pin Locks for TorkLift FastGun and Derringer Turnbuckle Handles #TLS9500 will all use the same key, however the TorkLift Tie Down Locks #TLS9700 will use a different set of keys as they are not able to be keyed alike.

view full answer...

Answer 5

Yes, both the Draw-Tite Front Mount Hitch part #65076 and the Curt hitch part #C31078 fit all models of the 2019 Ford F-250 Super Duty. They will not interfere with the front axle at all. I have attached photos showing how they install on the Ford…

view full answer...

Answer 6

The hitch pin will end up behind the air dam of your 2020 Ford F-250 when you install the Curt hitch part #C31078 on it. Once cut the air dam is very easy to flex so that you can access the hole as needed.

view full answer...

Answer 7

The Draw-Tite Front Mount Trailer Hitch Receiver part #65076 is a custom fit for all models of the 2020 Ford F-350 Super Duty so it will fit your diesel truck. The Draw-Tite hitch has a 9,000 lb line pull and 500 lb vertical load. The line pull is…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Front Hitch Recommendation for 2020 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching