Correct Shock Kit for 2013 Crossroads Zinger with LCI52 Axle

Question

Question:

The trailer is a 2013 Crossroads Zinger and the axles are LCI52-SB-86.5-68.5-NOSP-OS-L-65516-7225-30PT. Is this the correct shock kit, RM-2460? Thank you,

asked by: James B

0

Expert Reply:

Yes, LCI52 means you have a Lippert 5,200 Lb axle therefore the correct shock kit is the Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers part # RM-2460.

expert reply by: Conner L

0

Answer 1

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part #MR33WR.

view full answer...

Answer 2

The Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 5,200-lb to 7,000-lb Axle #RM-2460 is a great option. The leaf spring kit it was paired with is no longer available separately, so if you want both you would need to get the kit…

view full answer...

Answer 3

The MORryde X-Factor Crossmember #MR99ZR that you bought was designed to fit the MORryde LRE, RE, or TRE leaf spring setups which if that's what you have it would work great with that. The other components, the lift kit part #LC407131 and #MR46ZR…

view full answer...

Answer 4

You can get the longer U-bolts here; I checked with Roadmaster, and the 2630 are simply 7 inch long U-bolts, so you can use the following: - 3" Round Trailer U-Bolts (Qty 2) #SP01-060 These are 7 inches long so they are the same, and for a…

view full answer...

Answer 5

Since you have 7k axles the Roadmaster Comfort Ride kit part #RM-2460 would be what you'd need. There isn't any reason to go with an 8k version since the U-bolt plate it attaches to wouldn't match up to what you have. The flat part that…

view full answer...

Answer 6

The MORryde X-Factor Crossmember part #MR33WR is designed for standard suspension so that is the one you will need to use. If your leaf spring hanger brackets are wider than 3" then you will need to drill per the instructions which I have…

view full answer...

Answer 7

For absolute best results you'd install three of the MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension #MR99ZR but some people will use just two on a tandem setup and it will work great. If you check out the install…

view full answer...

Answer 8

Thanks for the picture of your axle label. From that we know you have Dexter 7k axles and that means the Roadmaster Comfort Ride part #RM-2460 that you referenced is the correct shock kit for it.

view full answer...

Answer 9

When installing the Roadmaster Comfort Ride Shock Absorbers #RM-2460 the distance is determined by the first shock you install. According to the instructions, optimum trailer handling is achieved when the shock is at approximately a 30 degree angle.…

view full answer...

Answer 10

The end plates on the MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension #MR99ZR measure 4" x 8". The mounting holes line up with the LRE, RE, and TRE brackets. See the dimensional drawing below.

view full answer...

Answer 11

I went ahead and reached out to my contact at MORryde, and she confirmed that the X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR will come with new mounting hardware. The plates on the cross member do add thickness, so the…

view full answer...

Answer 12

Yes the MORryde X-Factor Crossmember #MR99ZR that you referenced does fit trailers that have MORryde equalizers installed on them.

view full answer...

Correct Shock Kit for 2013 Crossroads Zinger with LCI52 Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching