Lift Kit for #10 Dexter Torflex Axle on Light Trailer

Question

Question:

I have a 2019 scout lite aliner. What kit would that take

asked by: RICHARD M

0

Expert Reply:

From what I can see in the photo it looks like you have a Dexter Torflex torsion axle, the #10 Torflex axle with a 2,500 lb capacity. Based on that the correct lift kit is the Torflex Lift Kit # K71-707-01.

However, it is important to make sure your trailer does not have 3" high-profile brackets. I have added a link to a video review for you to check out as well.

expert reply by: Kyle S

0

Answer 1

I can absolutely confirm the correct lift kit for your trailer. Based on your photos, you do in fact have a #10 Torflex axle, and they are compatible with the lift kits because you do not have 3" high-profile brackets (which just means the…

view full answer...

Answer 2

I went out to our warehouse to measure the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 6 on 5-1/2 #84655UC1 for you. It has an outside bore diameter of 3.09 inches that the center of the wheel will fit over. I've attached a photo to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Lift Kit for #10 Dexter Torflex Axle on Light Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching