Trailer Hitch Receiver and Wiring Harness for 2006 Chrysler Town and Country
Question:
I have a 2006 Chrysler town and country touring with a 3.8 L V6 engine. My van is handicapped accessible with the ramp. It also has an air compressor in the rear by the gas tank that lowers the rear end as the ramp lowers and retracts back. I want to be able to tow trailers I have.
asked by: Henry
Helpful Expert Reply:
You can tow your trailers, although please note that it is not possible to verify any type of fit for a trailer hitch on anything but fully stock in the area where the hitch will be installed. I can only offer the trailer hitches and trailer wiring harnesses that fit your 2006 Chrysler Town and Country as if it were stock, which are the following:
- If your van DOES have Stow-N-Go Seats: Draw-Tite Max-Frame Trailer Hitch Receiver # 75305
- If your van does NOTE have Stow-N-Go Seats: Draw-Tite Max-Frame Trailer Hitch Receiver # 75119
The correct wiring harness for your 2006 Chrysler Town and Country is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118300.
I have added links to installation videos of each of these parts for you to check out as well as links to the installation instructions.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Installation Instructions For The JR Products RV Cabinet Door Struts # 37270545
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Difference Between Square and Round Tube Trailer Hitches for 2010 Honda CR-V
- Q&A: ETBC7 Installation Recommendation for a 2005 Chrysler Town and Country
- Article: Trailer Hitch Receiver Sizes
- Q&A: Is Bumper Removed On Install Of Draw-Tite Trailer Hitch, # 75305, On 2007 Chrysler Town And Country
- Q&A: How To Find Lock Code for Keys To Camper
- Article: 2023 Best Gifts for Auto Enthusiasts
- Article: 2023 Best Gifts for Outdoor Enthusiasts
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: All Parts Needed to Tow With a 2007 Dodge Grand Caravan
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Trailer Towing Capacity of 2005 Chrysler Town & Country Touring Edition