Distance Between Mounting Holes of Brightway Breakaway Battery Box # 3802311

Question

Question:

Can you tell me the distance between the mounting holes for this unit?

asked by: Steve M

0

Expert Reply:

From left to right the mounting holes of the Brightway Breakaway Battery Box # 3802311 is 8-1/4 inches. Vertically they are separated by 1-3/16 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The shaft on which the crank attaches to for the Pro Series Square Jack, #PS1400950376, measures 1 inch in diameter. I have also included a dimensional diagram for the jack for you to view.

view full answer...

Answer 2

The main battery box included in the Bright Way Push-to-Test Trailer Breakaway Kit #3802308 is 6-1/2 inches wide by 4-3/4 inches deep by 4-7/8 inches tall. The mounting hole centers are 5.9 inches apart. The wire leads on the breakaway switch are…

view full answer...

Answer 3

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 4

It sounds like the magnets or their wiring could be bad. Your 2012 Chevy Silverado 2500HD is probably sensing the wrong resistance from the trailer brake magnets and that is why you see that warning message. When magnets have 2 of the same color wire…

view full answer...

Answer 5

For a breakaway system with a built-in charger I recommend the Bright Way Push-to-Test Trailer Breakaway Kit #3802311. This is a popular option because it is all in one and has a push to test feature to monitor battery charge level.

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Yes, the 12 volt accessory circuit of your trailer wiring would be able to keep a 10 amp breakaway kit battery topped off like the part #3802311. Usually the 12 volt accessory circuit of a 7-way is protected with either a 30 amp or 40 amp fuse.

view full answer...

Answer 8

I can indeed tell you the function and leads for each of the wire for the Dexter BrakeRite Electric Over Hydraulic Actuator for Disc Brakes #DX82KR. Here is what each is for, per the manual (which is also linked below): - White: 12V DC negative…

view full answer...

Answer 9

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 10

The hub bore diameter close to the base of the Dexter Trailer Idler Hub Assembly for 6,000-lb Axles #42655UC1 is just over 3-1/2". Please note that the hub you're asking about is a lug-centric hub which means it has the studs in place and…

view full answer...

Answer 11

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 12

The etrailer Magnetic Hitch Receiver Reducer Sleeve #e28JR is indeed magnetic. Now the whole thing is not magnetic, there are simply two magnets built in to the bottom of the adapter. See the picture below. We chose to add magnets as a…

view full answer...

Distance Between Mounting Holes of Brightway Breakaway Battery Box # 3802311

Product Page this Question was Asked From

Continue Researching