Does Curt Trailer Hitch Install on 2020 Kia Telluride Require Removing the Spare Tire

Question

Question:

For the 2020 Kia Telluride, the Curt hitch requires removing the spare tire? Correct? It goes back on though correct? Is there anything else to know about the install?

asked by: Henry E

0

Expert Reply:

When installing the Curt Trailer Hitch Receiver # C13420 on a 2020 Kia Telluride you do have to remove the spare tire; that is the first step but it does get put back into place at the end of the installation.

The install of this hitch is relatively straightforward with a number of different steps but nothing that requires any specific technical savvy. You will need to (temporarily) lower the exhaust and remove an underbody panel on the driver side, but apart from that you just raise the hitch into place, bolt it in and do some light fascia trimming on the underside of the vehicle (which won't be noticeable).

I have added links to the installation instructions as well as linked an installation video for you to check out of the Curt Trailer Hitch # C13420.

expert reply by: Kyle S

0

Mrwianno

3/5/2020

Distance from ground to top of 2 hitch square opening is 17 on factory hitch. What is the technical reasoning for Curt and Draw-Tite to have this dimension at 15 1/2? I would assume that it would be preferred to have hitch higher off the ground. Should be a very good reason for this difference.

Reply

Chris R.

3/6/2020

The higher ground clearance for the OEM hitch is just a result of the receiver protruding more through the bumper fascia (instead of resting directly below it like the aftermarket models). This is the case with a lot of factory hitches because it creates a sleeker appearance. Curt and Draw-Tite likely have the receiver below the bumper just so the customer doesn't have to cut as much on the bumper during installation. You're right that it's always nice to have more ground clearance, but you still shouldn't have any issues with the 15-1/2" dimension on the aftermarket hitches.

Reply

Answer 1

As long as this bumper plate fits in place of the original bumper panel, it could provide an alternative to having to trim the bumper panel during installation of the Curt Trailer Hitch Receiver #C13420. The hitch is a confirmed fit while we…

view full answer...

Answer 2

If your 2022 Kia Telluride does not have any of the wiring for adding a tow package you will need the Upgraded Heavy Duty ModuLite Circuit Protected Vehicle Wiring Harness #C59496 to tie into the tail light wiring for a 4-way flat trailer connector.…

view full answer...

Answer 3

Your 2022 Kia Telluride is compatible with hitch receivers from Curt and etrailer. Here are the main features of each option. The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2", part #C13420, has a maximum tongue weight of 750 lbs and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Does Curt Trailer Hitch Install on 2020 Kia Telluride Require Removing the Spare Tire

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching