Will Ultimate Trailer Jack Sit Flush With Collar For Tailgate Clearance

Question

Question:

regarding Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2inch Lift - 2,000 lbs Item # 322-RDJ-2K. I know the minimum distance between the top of the handle and bottom of collar plate is 7 1/4 inch in the lowest lockedinch position. Will the tube slide further down into the collar if it is not in a lockedinch position? I need just 2 inch of additional clearance to allow my tail gate to be fully lowered w/o hitting the top of the jack.

asked by: Tim O

0

Expert Reply:

The Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs part # 322-RDJ-2K will not sit flush with the collar even when unpinned. The jack locks into place automatically. There will be about 7-1/4" from the collar to the top of the handle which is actually low profile clearance compared to some of the other jack options that have 11 inches or more. This is going to be the lowest profile option we have at this time. The handle of the Ultimate Trailer Jack folds down as well so that won't be sticking up. I have attached photos for your reference.

Another option is to use a longer ball mount which will push the trailer away from the vehicle further for tailgate clearance. I recommend to use Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs # BM20 which will give you the additional length to your setup for clearance.

expert reply by: Heather A

0

click to enlarge

Answer 1

I went out to the warehouse and found that the distance from the center of the jack to the furthest part of the adjustment pin on the Ultimate Trailer Jack #322-RDJ-2K when it is pulled out is 5-3/8". If you have this much room from the center…

view full answer...

Answer 2

The Go Power Portable Solar System #34282730 that you referenced should work great to keep the 12V battery in your Lancer camper topped off. In reality it's going to depend on just how much power you will be drawing (how many accessories you…

view full answer...

Answer 3

The standard RV battery is a 100 amp hour deep cycle AGM battery like the part #BRW94FR which will work great. If you wanted to go with something that would last longer the Lithium part #34282738 is going to last even longer between charges and will…

view full answer...

Answer 4

There was indeed a recall on the Lippert Smart Jack Electric Trailer Jack part #LC643589. It sounds like you have a pre-recall version but in order to confirm you can look on the back of the jack for a sticker on the stem with a serial number. If…

view full answer...

Answer 5

The dual battery box part #329-HM426 would fit two of the Go Power Sun Cycle Solar RV Battery #34277606 that you referenced. The outside dimensions of the box are also compatible with the space you mentioned having as well.

view full answer...

Answer 6

Lithium batteries really are much nicer than lead acid batteries in terms of how well they hold a charge. There is a much bigger investment required though as the batteries themselves are more expensive you need to use chargers designed for them…

view full answer...

Answer 7

If you're looking for the hard plastic piece that covers the manual override on your Lippert Smart Jack Electric Trailer Jack #LC643589, you can use part #LC733925. Aside from that and the drop leg #LC405217, Lippert does not offer any other…

view full answer...

Answer 8

I spoke with Go Power and they confirmed you can in fact combine more than one Go Power Portable Solar Panel #34282610 but they would all have to go through one controller which would require some modification to the wiring. However, they also…

view full answer...

Answer 9

Lithium batteries do need a higher voltage charge than standard batteries so you will need to replace your converter so for a 30 amp charger/converter you'd want the part #PD9130LV. For a lithium batteries then the part #GP99QR is a 100 amp…

view full answer...

Answer 10

The distance from the bottom of the mounting flange to the bottom of the outer tube on the Bulldog Round, A-Frame Jack part #BD155033 is 3-1/2". The mounting flange is 3/16" thick. I have attached a photo of these measurements for you as…

view full answer...

Answer 11

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I have…

view full answer...

Answer 12

I went out to our warehouse to take some measurements on the Pro Series A-Frame Jack #PSEA20000103 that you referenced and found that there is a distance of 11 inches from the mounting bracket just to the top of the jack tube. From the mounting…

view full answer...

Will Ultimate Trailer Jack Sit Flush With Collar For Tailgate Clearance

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching