Is Wiring Adapter Harness Needed to Install Brake Controller on 2007 Chevy Silverado New Body

Question

Question:

Is mounting bracket included with this product. Is there a direct plug wiring adapter for 2007 chevy silverado truck. I can not find one on your web sight

asked by: David

1

Helpful Expert Reply:

The Tekonsha P3 brake controller you'd looked at, part # 90195 actually includes 2 different mounting brackets, as shown in the provided photo. The 2007 Silverado New Body actually doesn't need a brake controller wiring harness, the tow package wiring bundle is located under the dash above where the drivers left knee would be, between the emergency brake pedal and the steering column. Look for a bundle of wires with a white tag on them. The bundle will contain 4 or 5 blunt-cut wires that would wire to the brake controller as follows:

Tow package red/black wire connects to black wire on controller
Tow package white wire connects to white brake controller wire
Tow package white/blue striped wire connects to red brake controller wire
Tow package dark blue wire connects to blue brake controller wire

The orange wire isn't needed. I'll link you to a help article that further addresses this. The article includes photos showing exactly where the tow package harness is located.

expert reply by: Mike L

1

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 7

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 8

The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake…

view full answer...

Answer 9

To install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 in your Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply terminated with tape. You will…

view full answer...

Answer 10

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...