Hook Size for BoatBuckle G2 Retractable Gunwale Tie-Down Straps IMF14221

Question

Question:

Whats the inside width of the hook? The gunwale around my rowboat is rather wide and Im concerned about fit.

asked by: Mike C

0

Expert Reply:

The inside width of the hook on the BoatBuckle G2 Retractable Gunwale Tie-Down Straps # IMF14221 measures just over 2". These hooks are designed to fit gunwales that are 2" wide or less.

I have attached a short video demonstration below that you can also check out.

expert reply by: Chris R

0

Answer 1

I spoke with my contact in the Tech Services department at Fulton, who explained that Aluminum trailer frames have a greater wall thickness than a steel frame. The bolts that attach the hinge to the trailer frame have a large diameter shoulder…

view full answer...

Answer 2

The Fulton Fold-Away Coupler Hinge Kit for 2" x 3" Tongue #FHDPB230101 is designed for a 2"x3" trailer tongue, but we have heard of customers welding a 1/2" spacer to each side of their…

view full answer...

Answer 3

All of the needed install hardware for the Fulton Hinge Kit part #FHDPB230101 that you referenced comes with the kit. You would not need to provide your own.

view full answer...

Answer 4

I don't recommend just using washers to shim the Fulton Fold-Away Coupler Hinge Kit for 2" x 3" Trailer Tongue - Bolt On - Up to 5,000 lbs #FHDPB230101. A small steel plate - with more overall area then washers - should be…

view full answer...

Answer 5

For your 2 inch tongue the Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lb #CT-3001-Z is my recommendation. Then I'd use the Fulton Fold-Away Coupler Hinge Kit for 2" x 3"…

view full answer...

Answer 6

The reason the wall thickness is listed for the Fulton Fold-Away Coupler Hinge Kit, part #FHDPB230101, is because the Torx bolts included in the kit are a certain length and the nuts may not catch the threads when installing the hitch due to the 1/4…

view full answer...

Answer 7

For your aluminum trailer with a galvanized steel tongue (swing-away tongues cannot be used on aluminum tongues), you'll need a die-cast steel tongue with a zinc finish from Fulton. The correct fit is going to depend on the size of your trailer…

view full answer...

Answer 8

Fulton hinge kit #FHDPB230101 is designed to bolt onto a steel tongue that is 2 x 3 inches. Galvanized steel is still steel so provided that the trailer manufacturer doesn't have any objections and the tongue is the right size you will be good to…

view full answer...

Answer 9

Yes, the Fulton Fold-Away Coupler Hinge Kit part #FHDPB230101 will work on a 2" x 2-3/4" frame but you will need to install spacers in order to fill the 1/4" gap or 1/8" on each side. I suggest some flat metal washers for this.

view full answer...

Answer 10

The required thickness of the metal on your 2" x 3" trailer tongue is between .188" and .120" in order to use the fold-away coupler, which is the following part number: - Fulton Fold-Away Coupler Hinge Kit for 2" x 3"…

view full answer...

Answer 11

I recommend using the Fulton Fold-Away Coupler Hinge kit part #FHDPB230101 that fits a 2"x3" trailer tongue. It comes with all the hardware needed to install. Please keep in mind the trailer tongue material thickness must be…

view full answer...

Answer 12

Channel Tongue Trailer Coupler #CT-3001-Z requires a 2 inch wide tongue but I recommend a boxed tongue and not C-channel so there is more support where it counts. Steel tubing at least 1/8 of an inch of wall thickness will do the trick. The length…

view full answer...