Are There Replacement Parts for the A-Frame Trailer Coupler w/ Round Jack Hole CA-5280-RB

Question

Question:

Do you have Replacement Parts for the A-Frame Trailer Coupler w/ Round Jack Hole - Squeeze Latch - Black - 2-5/16inch Ball - 15,000 lbs Item # CA-5280-RB?

asked by: Brian

0

Expert Reply:

I do have weld-on, a-frame trailer couplers in which replacement parts are available but the A-Frame Trailer Coupler w/ Round Jack Hole part # CA-5280-RB is not one of them. The Demco 50-Degree A-Frame Trailer Coupler part # 12660-97SP and Bulldog Heavy-Duty Cast Head Coupler part # BD44150W0317 both have replacement coupler repair kits, the Demco Composite eZ-Latch Repair Kit part # DM6008 and the Repair Kit Fulton Wedge-Latch Cast Head Coupler part # F670801.

I recommend the Demco 50-Degree A-Frame Trailer Coupler because the eZ-Latch mechanism is very simple to use, just drop the coupler over the hitch ball and the latch will snap into place. The Demco 50-Degree A-Frame Trailer Coupler can then be painted to match the trailer frame with a can of spray paint.

expert reply by: Conner L

0

Answer 1

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 2

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will…

view full answer...

Answer 3

The play you are feeling/hearing is most likely between the hitch ball and the latch of the coupler. If you look under the coupler you can see an adjustment bolt that uses an Allen wrench that will allow you to tighten the latch and get rid of the…

view full answer...

Answer 4

The big difference between the two couplers you mentioned is that the Demco #DM13205-95 does not come with chain anchors and the part #DM16680-52 does.

view full answer...

Answer 5

I went and pulled a coupler like you have part #BD44150W0317 and the coupler lock you are interested in part #BLTL-20 and found that they lock is wide enough to fit this coupler. I attached a picture that shows the two products next to each other…

view full answer...

Answer 6

We offer three cast head 2-5/16-Inch A-Frame Couplers that carry a higher weight rating than the 14,000-lb-rated Fulton #F44314R0303 coupler that you referenced. The link provided will show you each of these 15,000-lb-rated wedge latch couplers from…

view full answer...

Answer 7

I went out to our warehouse to measure the Bulldog Heavy-Duty Cast Head Coupler #BD44150W0317 that you referenced and found a distance of right at 15-1/4 inches from the front of the coupler to the center of the jack mounting hole. The other…

view full answer...

Answer 8

The style of coupler you have now on your horse trailer is a Bulldog Collar Lok style which is very common on horse trailers. The Bulldog Wedge Latch Coupler part #BD44150W0317 will fit perfectly on your trailer as thankfully the angles of the…

view full answer...

Answer 9

It sounds like you're looking for a replacement a-frame coupler like #CA-5280-RB but in a silver-painted or zinc-plated finish. Please click on the link provided to see all bolt-on standard a-frame couplers for 2-5/16-inch balls. For the…

view full answer...

Answer 10

The best lock recommendation we'd have for your Bulldog Coupler part #BD44150WH301 would be the Fastway Lock part #FA86-0015-316. Although this is a universal style coupler lock it's design allows it to fit basically all coupler styles well…

view full answer...

Answer 11

I took a look at the instructions of the Bulldog Heavy-Duty Cast Head Coupler w/ Wedge Latch #BD44150WH301 and it specifies using grade 5 bolts with lock nuts. However, there is not a specified length for the bolts, and that will simply depend on the…

view full answer...

Answer 12

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

view full answer...

Are There Replacement Parts for the A-Frame Trailer Coupler w/ Round Jack Hole CA-5280-RB

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching