Installation Instructions for Solera Family Room for RV Awning

Question

Question:

Solera room installation

asked by: Mary K

0

Expert Reply:

Installing the Solera Family Room for 21' RV Awning # LC362236 isn't necessarily a difficult task, just a bit of a long process since it involves some precise measurements to make sure everything lines up correctly.

Attached is a link to the instructions for you to check out. I would clip and post pictures right to this page but the instructions are a little extensive and wouldn't fit well.

expert reply by: Jon G

0

Answer 1

To enter/exit the Solera Screen Room for 21' RV Awning #LC362224, you should just be able to roll the door flap up as shown in the image attached.

view full answer...

Answer 2

The Solera 20' Sand Fade w/ Black Weather Guard RV Awning (Std) #LCV000231498 will work very nicely with the Solera Family Room #LC362235. I've attached the instructions in photo form to assist with the installation.

view full answer...

Answer 3

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 10

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 12

I spoke with my contact at Progressive Dynamics and they informed me that the Lithium Converter for WFCO RV Power Centers part #PD4655LIV does work as an upgrade for the Parallax 7355. It has the same housing as the Replacement Converter for…

view full answer...

Installation Instructions for Solera Family Room for RV Awning

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching