Replacement Hardware For BAKFlip G2 Hard Tonneau Cover BAK26406 On Toyota Tacoma

Question

Question:

Lost my mounting hardware for my G2 during move. Just wanted to make sure that this hardware kit would work for a G2 on a 2015 Tacoma with the 5 foot bed

asked by: Roger

0

Expert Reply:

I do have an option for you but the hardware referenced is not a fit for the Tacoma. The Replacement Mounting Hardware Kit for BAKFlip G2 Hard Tonneau Cover part # BAKBK-200KIT is the replacement hardware for BAKFlip G2 hard tonneau cover # BAK26120 which is designed for Chevy trucks.

The 2015 Toyota Tacoma 5 foot bed uses the BAKFlip G2 Hard Tonneau Cover part # BAK26406 and the replacement hardware for that is part # BI37VR.

expert reply by: Heather A

0

Answer 1

I checked with Extang and the correct replacement drain for your Extang Xceed tonneau cover is the Replacement Rail Drain Tube item #EX31620024. This one fits both sides. The Extang drain tube is slightly bigger than the BAKFlip so I would…

view full answer...

Answer 2

We do have one-sided ladder racks but they are designed for standard cargo like lumber or a ladder. Since you're needing to carry a kayak I recommend going with a full ladder rack system for your 2018 Nissan Titan. The best option is the…

view full answer...

Answer 3

Yes the Yakima Overhaul HD Ladder Rack part #Y01151-58 that you referenced does come with 68 inch long crossbars.

view full answer...

Answer 4

With the BakFlip G2 tonneau part #BAK26406 you have the option of drilling a hole in the bed of your truck or using one of the current plugs of the truck bed for the drain hose. I attached a picture for you to see what is recommended.

view full answer...

Answer 5

For your husband's 2014 Toyota Tacoma with the deck rail system the best choice we have for a ladder rack is the adjustable height Yakima Overhaul HD part #Y01151-5868 which installs easily and gives you a ladder rack you can adjust high enough…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Replacement Hardware For BAKFlip G2 Hard Tonneau Cover BAK26406 On Toyota Tacoma

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching