Recommended Replacement Drain Tube for a Extang Xceed Tonneau Cover

Question

Question:

Will the drain tube for the BAKFlip Truck Bed Tonneau cover work with the Extang Xceed cover? I need to replace the drain tubes but cant one specific to the Xceed.

asked by: David

0

Expert Reply:

I checked with Extang and the correct replacement drain for your Extang Xceed tonneau cover is the Replacement Rail Drain Tube item # EX31620024. This one fits both sides. The Extang drain tube is slightly bigger than the BAKFlip so I would recommend using the replacement one from Extang.

expert reply by: Jerred H

0

Answer 1

With the BakFlip G2 tonneau part #BAK26406 you have the option of drilling a hole in the bed of your truck or using one of the current plugs of the truck bed for the drain hose. I attached a picture for you to see what is recommended.

view full answer...

Answer 2

We do have one-sided ladder racks but they are designed for standard cargo like lumber or a ladder. Since you're needing to carry a kayak I recommend going with a full ladder rack system for your 2018 Nissan Titan. The best option is the Yakima…

view full answer...

Answer 3

For your husband's 2014 Toyota Tacoma with the deck rail system the best choice we have for a ladder rack is the adjustable height Yakima Overhaul HD part #Y01151-5868 which installs easily and gives you a ladder rack you can adjust high enough…

view full answer...

Answer 4

I do have an option for you but the hardware referenced is not a fit for the Tacoma. The Replacement Mounting Hardware Kit for BAKFlip G2 Hard Tonneau Cover part #BAKBK-200KIT is the replacement hardware for BAKFlip G2 hard tonneau cover #BAK26120…

view full answer...

Answer 5

We do sell the seals for Extang tonneau covers. Based on your description and the lock that you bought previously, it looks like you have the Extang Encore Trifold Hard Cover. The correct cab seal for the Extang Encore Trifold Hard Covers is…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Recommended Replacement Drain Tube for a Extang Xceed Tonneau Cover

Product Page this Question was Asked From

Continue Researching