Version of B and W Rail Kit BWGNRM1067 that Comes with Center Hitch Section

Question

Question:

Does everything come in a kit from start to finish for BWGNRM1067 ? How many thousand pound is this hits rated for ?

asked by: Jeffrey W

0

Expert Reply:

The # BWGNRM1067 is just the rail kit and does not come with the center hitch section. The part number you need instead that comes with everything is the part # BWGNRK1067. This is rated for towing a trailer up to 30,000 lbs. The vertical weight capacity of the hitch is 7,500 lbs.

I attached an install video for this kit for you to check out as well.

Here's a list of all of the trucks this fits:

2008 - 2010 GMC Sierra 2500 - 6-1/2 Foot Bed

2007 - 2007 GMC Sierra New Body 2500 - 6-1/2 Foot Bed

2008 - 2010 Chevrolet Silverado 2500 - 6-1/2 Foot Bed

2007 - 2007 Chevrolet Silverado New Body 2500 - 6-1/2 Foot Bed

2008 - 2010 GMC Sierra 2500 - 8 Foot Bed

2007 - 2007 GMC Sierra New Body 2500 - 8 Foot Bed

2008 - 2010 Chevrolet Silverado 2500 - 8 Foot Bed

2007 - 2007 Chevrolet Silverado New Body 2500 - 8 Foot Bed

2001 - 2004 GMC Sierra 2500 HD - 6-1/2 Foot Bed

2001 - 2006 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed

2007 - 2007 Chevrolet Silverado Classic 2500 HD - 6-1/2 Foot Bed

2001 - 2004 GMC Sierra 2500 HD - 8 Foot Bed

2001 - 2006 Chevrolet Silverado 2500 HD - 8 Foot Bed

2007 - 2007 Chevrolet Silverado Classic 2500 HD - 8 Foot Bed

2005 - 2006 GMC Sierra 2500 HD Series - 6-1/2 Foot Bed

2007 - 2007 GMC Sierra Classic 2500 HD Series - 6-1/2 Foot Bed

2005 - 2006 GMC Sierra 2500 HD Series - 8 Foot Bed

2007 - 2007 GMC Sierra Classic 2500 HD Series - 8 Foot Bed

2008 - 2010 GMC Sierra 3500 - 8 Foot Bed

2007 - 2007 GMC Sierra New Body 3500 - 8 Foot Bed

2008 - 2010 Chevrolet Silverado 3500 - 8 Foot Bed

2007 - 2007 Chevrolet Silverado New Body 3500 - 8 Foot Bed

expert reply by: Jameson C

0

Answer 1

While we don't have a replacement hardware kit we can offer you for the #BWGNRK1016 I did attach a picture that shows all of the hardware you'd need that you could source at a local hardware store. I also attached an install video…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Version of B and W Rail Kit BWGNRM1067 that Comes with Center Hitch Section

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching