Is ICC Bumper Required to Install Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper

Question

Question:

Can I get this bumper without the ICC bumper?

asked by: Jon B

0

Expert Reply:

I reached out to the manufacturer, Buyers Products, who told me an ICC bumper is NOT required on your truck in order to install the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount # 3371809050 or the same bumper with 2" Receiver # 3371809055.

expert reply by: Kyle S

0

Answer 1

If your 2001 Ford F-450 features a flat or dump bed, the Buyers Products Hitch Plate Bumper #3371809055 will fit and work well. This is designed for cab and chassis trucks like yours with the nominal 34" frame width. Hardware is not included…

view full answer...

Answer 2

Most RV bumpers have a plastic plug on each end, so the interior of the bumper can be used for storage. You should be able to remove the plug and look inside the bumper to see how the seam is welded, one continuous weld or a series of spot welds. A…

view full answer...

Answer 3

The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver #3371809055 is designed or flatbeds and flatbed dump trucks. While it is ready to mount on Ford trucks, there is some drilling required for GM trucks. This hitch is a…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15845 will come down about 8 inches from the frame. It does add some support to help with an underrun in a rear end collision so as long as the drop is enough but…

view full answer...

Answer 5

The Buyers Products hitch #3371809050 that you referenced would fit a 1995 Ford F-350 with a dump bed as this fits the standard 34 inch frame of trucks that have dumb beds. These trucks are commonly sold as cab and chassis models which all have the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is ICC Bumper Required to Install Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching