Will the Derale Transmission Pan # D14208 Fit a 2000 Ford Excursion with 4R100 Transmission

Question

Question:

i have a 2000 ford excursion with a v10 gas motor and a 4r100 trans.. Just wondering if this pan will fit? Derales website says fits most. I know that the diesel 4r100 and gas 4r100 have different bellhousing bolt patterns , but not sure about the pan bolt patterns.

asked by: Jeff B

0

Expert Reply:

Derale has indicated that transmission cooler pan, # D14208 will fit the Ford diesel motors or gas motors if they have the 4R100 transmission. They do not have different models depending on the engine type, just transmission type. I have included a link to other coolers that are also recommended for your 2000 Ford Excursion, and some FAQ information for you.

expert reply by: Michael H

0

Answer 1

The Derale pan style transmission cooler #D14208 will fit your 1994 Ford F-150 with the 4.9 liter engine and E4OD transmission. You will not need to change the dipstick to test the fluid level.

view full answer...

Answer 2

My technical contact at Derale confirmed that you will use your stock transmission filter on your 1997 Ford F-350 Powerstroke when installing the Derale Transmission Pan Cooler #D14208. To install this properly your truck must have either the E4OD,…

view full answer...

Answer 3

There are virtually no structural differences between the Curt Front Mount Trailer Hitch Receiver part #31114 and the Draw-Tite Front Mount Trailer Hitch Receiver part #65022 for your 2000 Ford F-250. They both install in the exact same location and…

view full answer...

Answer 4

Yes, the Derale Transmission Pan Cooler #D14208 will fit your 1997 Ford F-350 PSD 4x4 with the E40D automatic transmission. The pan does have a 1/8" NPT port for adding a temperature sending unit.

view full answer...

Answer 5

If the test port on the transmission of your 1999 Ford F-250 uses thread dimensions that are 1/8 NPT then the sensor of the #D13009 would fit and work well. In the instructions I attached this is basically the Option 2 set instructions listed. Option…

view full answer...

Answer 6

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...