Which Front Hitch Installs Higher for 2020 Ford F-250 Curt or Draw Tite

Question

Question:

My 2020 Ford F-250 has the taller lower air dam on the front of the truck and I want to know if the Curt or the Draw Tite cuts a hole in it to install and which sits higher/lower.

asked by: Troy

0

Expert Reply:

I attached pictures that show how the Curt front hitch # C31078 and the Draw Tite # 65076 looks when installed and you can tell that the Draw Tite sits up a bit higher since it comes through relative to the curve in the air dam.

expert reply by: Jameson C

0

click to enlarge

Answer 1

There are two front hitch options we have for your 2018 Ford F-250 which are very similar. We have the Draw Tite part #65076 and the Curt #C31078 which are both really great options. The big differences are that the Draw Tite will stick out past…

view full answer...

Answer 2

Adding a front hitch to your 2017 Ford F-250 Diesel 4x4 Off Road will reduce your bumper clearance in the front by about 3 inches but if you have the air dam on the front, that will hang lower than the receiver. I recommend the Curt #C31078 over…

view full answer...

Answer 3

We have two really great front hitches that fit your 2020 Ford F-250 with the Draw Tite part #65076 and the Curt #C31078. The big differences are that the Draw Tite will stick out past the air dam a bit more than the Curt. Also the Curt is made in…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Which Front Hitch Installs Higher for 2020 Ford F-250 Curt or Draw Tite

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching