Is Play Between Hub and Axle on Trailer Normal

Question

Question:

I have had this trailers for 3 months. I feel like the trailer is louder going over bumps compared to when I first got it. It seems to be coming from where hubs connect to the axle. Although I feel the lug nuts are tight, When I pull the tire there is play between the hub and the axle. Is this normal or is it indicative of a possible issue?

asked by: Marc M

0

Expert Reply:

If the tires on your CE Smith Multi Sport Boat and Kayak Trailer # CE48810 have some play then that would definitely be contributing to what you're hearing. If the lugs are tight then this means that your spindle nut needs to be tightened down as you shouldn't be able to see any movement with your hub.

Tighten your spindle nut until you don't have anymore play and then back it off to the next notch. This should take out the play you have found as well as the weight noise you are hearing.

Let me know if you're having any other issues and I can help you troubleshoot further.

expert reply by: Jon G

0

Answer 1

The least expensive option we can offer you to transport the Sun Dolphin Water Tender Dinghy is with the CE Smith Multi Sport Boat Trailer part #CE48810. This boat trailer will be perfect for you as it comes with everything you need to hit the…

view full answer...

Answer 2

I recommend using something like the CE Smith Multi Sport Trailer #CE48810. This one is a bunk style which I like using with heavier boats like your 77lb kayak. This trailer is for a 12 foot boat and it comes with load range B tires so it's rated…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Is Play Between Hub and Axle on Trailer Normal

Product Page this Question was Asked From

Continue Researching