Adding Brakes to 1999 Jayco Heritage Glacier with Dexter 2,500 lb Axles

Question

Question:

Howdy - hoping to find part numbers for wheel seals, bearings, and electric brake conversion kits that will fit my 1999 Jayco Heritage Glacier popup. The axle is marked 2500lb / Dexter P-12 SLR SN 3225916 / Jayco 206491-1 SN D3225916. Thanks in advance!

asked by: Andrew

0

Expert Reply:

A Dexter 2,500 lb axle uses hubs that have inner and outer bearings of L44649 like the part # 8-257-5UC3 which has a 5 lug bolt pattern or the # 8-173-16UC3-EZ which has a 4 lug bolt pattern. These both come with bearings and seals as well.

For brake assemblies you'd want the part # 23-47 for the left hand side and # 23-48 for the right hand side and you'd be set. I attached a help article link on adding electric brakes to a trailer for you to check out as well that I think you'll find helpful.

expert reply by: Jameson C

0

Answer 1

If by tail light cover you mean a replacement lens then we do have a wide selection of these so there is a chance we may have what you need but I don't have any sort of parts breakdown sheet for a 1999 Jayco Eagle Pop-Up Camper so in order to see…

view full answer...

Answer 2

We checked with Dexter and P-12 just indicates where the axle was made. With the serial number we could track down more info on your axle. However, in the mean time you could pretty easily get the bearing numbers off of your current bearings and then…

view full answer...

Answer 3

We can help you select new 5.30-12 tires or this size tire pre-mounted on a 4-lug wheel if you prefer. All the 5.30-12 tires we offer are bias ply types; no radial tires are offered in this size. I suggest you use a Load Range D tire, part #AM10068…

view full answer...

Answer 4

Atwood is no longer in business, which means replacement parts are unfortunately no longer available for your Atwood 61101 surge brake actuator. The best option available if yours is no longer working is to replace the actuator, which you can do with…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...