What Size Hole Normally Gets Drilled to Install 7-Way

Question

Question:

What size hole needs drilled to flush mount this plug

asked by: Tyler L

0

Expert Reply:

The mounting brackets that normally hold 7-ways like the # C55416 that you referenced typically have a 2 inch center diameter like the part # PK12711U. If you were wanting to drill a hole in a surface to mount this into I'd go with a 2 inch hole for the easiest install.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Curt Mounting Bracket #C67UR is the bracket that I recommend using with the Curt 7-Way RV-Style Trailer Connector #C55416 that you already have. This connector uses a mounting bolt pattern of 2-1/4" X 1-1/2". The EZ Connector Mounting…

view full answer...

Answer 2

The main difference between the Curt 5th Wheel/Gooseneck Custom Wiring Harness part #C56070 and the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness part #41157 is that the Curt harness is 7' long and comes with a one year warranty…

view full answer...

Answer 3

The biggest difference will be price. The two harnesses are basically the same harness made by two different companies. The Curt part #C55382 would be what I would go with over the Hopkins #42475 because the price is better and because we seem to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...