Rear Bumper for 1993 Jeep YJ with Curt Hitch Already Installed

Question

Question:

I currently have the Curt hitch receiver on my 93 Jeep YJ. Is there a bumper that will mount with this receiver without modifications?

asked by: Jerryl A

0

Expert Reply:

Based on how the Curt Class III Hitch Receiver # 13657 mounts to your 1993 Jeep YJ, we don't have a rear bumper available that can be installed with the hitch in place without some significant modifications.

All of the aftermarket bumpers we have for the YJ though include their own integrated 2" receiver, such as with the Rampage # RA7648, so your best option may be to simply remove the existing hitch altogether if you are wanting to add a bumper like this. I have attached the complete installation manual for this particular bumper, along with a link that will take you to our available selection.

expert reply by: Chris R

0

Answer 1

Hey Scott, sorry for the confusion but the Curt hitch part #C45FR that fits your 2022 Tesla Model 3 does have a tongue weight capacity of 300 lbs. I confirmed this with Curt just now.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Rear Bumper for 1993 Jeep YJ with Curt Hitch Already Installed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching