Replacement Bearing Kit For Forest River Cedar Creek Silverback

Question

Question:

I have a Forest River Cedar Creek Silverback 32foot travel trailer with 3500 lb axles. I bought the 4 electric assemblies 4 years ago and want to be sure I have the correct bearing kit below. Please advise. Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal Item # BK2-100

asked by: Frank D

0

Expert Reply:

Since trailer manufacturers do not make specific trailer information widely available to the public such as bearing numbers. I cannot tell you the bearing kit that the Forest River Cedar Creek needs. However, if you want to measure your spindle you can be sure the bearing kit will fit. You can also check the bearings for bearing numbers stamped on the side of the bearing.

Bearing Kit for #84 Spindle part # BK2-100 consists of outer bearing part # L44649 which measures an inner diameter of 1.063". The inner bearing is part # L68149 which measures 1.378". The seal is inner diameter 1.719" and outer diameter 2.565". I have attached a diagram so that you can compare where the bearings and seal sit to the diameter of your spindle.

expert reply by: Heather A

0

click to enlarge

Answer 1

I do have an option for you but I cannot give you exact bearing numbers for your trailer unless provided with spindle measurements or the trailer's VIN (if the manufacturer is still in business). I can however tell you that the two most common…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Replacement Bearing Kit For Forest River Cedar Creek Silverback

Product Page this Question was Asked From

Continue Researching