Can Two Thule Hullavator Be Installed On a Yakima OverHaul HD with 78 Inch Bars

Question

Question:

Will two Thule hullivators fit on a Yakima Overhaul HD with 78 inch cross bars above the bed on my 2015 F-150 5.7inch bed?

asked by: Chris

0

Expert Reply:

Each of the Thule Hullavator Pro Kayak Carrier part # TH898 requires 28.5" of load bar space to mount which means you would indeed be able to fit two on the 78" Yakima OverHaul HD Adjustable Truck Bed Ladder Rack part # Y01151-59.

expert reply by: Conner L

0

Answer 1

If your factory crossbars extend 4 to 8 inches past the roof rack foot that attaches the crossbars to the roof, the Thule #TH898 Hullavator Pro kayak carrier will work for you. If the crossbars do not extend past the roof rack feet by that amount,…

view full answer...

Answer 2

In order to use the Thule Hullavator Pro Kayak Carrier and Lift Assist part #TH898 on a 2020 GMC Sierra 3500 Crew Cab I recommend the Thule WingBar Evo Crossbar System composed of part #TH711520, part #TH710501, and part #TH145071. This system is one…

view full answer...

Answer 3

You may be able to fit two Thule Hullavators #TH898 on the roof of your 2021 Mazda CX-5, but it will require at least 57" of crossbar space along with a decent weight capacity since each Hullavator weighs 40lbs empty. I do not see raised roof…

view full answer...

Answer 4

Yes, the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs TH897XT (NLA) can fit on both square-bars, as well as on the Yakima CoreBars, like the Yakima CoreBar Crossbar - Steel - Black - 70" Long #8880655. Attached are a couple…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 12

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...