Replacement Hardware Kit for Trailer Hitch on a 2000 Jeep Cherokee

Question

Question:

I was wondering if you sold and what the item # was for a Replacement Hardware Kit for a Trailer Hitch for a 1999 Jeep Cherokee Sport 4.0l - 6cyl. Thanks for your time,.

asked by: Drew B

0

Expert Reply:

It looks like the hardware for the trailer hitch will be the same no matter what actual hitch you have so in order to obtain a replacement hardware kit to install a trailer hitch on your 2000 Jeep Cherokee you can use the Replacement Hardware Kit for Trailer Hitches part # RHK. Once you get to the product page you can enter "13084" into the hitch item number box and select "Curt" form the manufacturer drop drown menu. This will give you the correct hardware whether you have a Curt hitch, Draw-Tite hitch, or Factory hitch.

expert reply by: Conner L

0

Answer 1

Typically when people remove a trailer hitch receiver that uses bolts that need to be installed using a fishwire like those found on the Curt Trailer Hitch Receiver #C11529 for your 2020 Hyundai Kona, they carefully remove the hitch and reinstall the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Replacement Hardware Kit for Trailer Hitch on a 2000 Jeep Cherokee

Product Page this Question was Asked From

Continue Researching