Is There a Way to Lock Ball Mount Platform to Channel of BulletProof Adjustable Ball Mount

Question

Question:

Id like to replace the 2 5/8inch mounting pins with a locking type . . I need to know what the span is?

asked by: Roger

0

Expert Reply:

We offer the InfiniteRule Hitch Lock for 3" Hitches # 34065034 that we know fits and works great to lock the ball mount platform of the BulletProof Hitch # MD206 that you referenced. The span of this is 3-7/8 inches and the diameter is 5/8 inch.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 4

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Answer 10

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Answer 11

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 12

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...