Draw-Tite Max-Frame Hitch Fit on a 2007 Chrysler Town and Country With Back-up Alarm
Question:
Will p/n 75305 fit with the back-up alarm strip that runs along the bottom of the bumper ... down about to the centerline of the exhaust where it has a half round cutout in that panel ?
asked by: Jerry B
Expert Reply:
I spoke with my contact for Draw-Tite and he said the Draw-Tite Max-Frame Trailer Hitch, # 75305, should fit on your 2007 Chrysler Town and Country as long as the back-up alarm strip is not sitting below the bottom of the bumper fascia. If the back up alarm strip that you are referring to are the factory back up sensors that mount in the holes at the bottom of the bumper, then they will not interfere with this hitch. Any aftermarket products that have been attached to the bottom of the bumper fascia must be removed before installing a hitch on your vehicle.
This hitch will only fit your vehicle if you have Stow-N-Go seats. If you do not have Stow-N-Go seats, then you will want the Draw-Tite Trailer Hitch, # 75119. All of the hitches we offer will mount with the receiver against the bottom of the bumper fascia.
If you plan on doing any towing with this hitch then you may want to pick up the T-One Wiring Harness, # 118300, and the Ball Mount Kit, # EBMK4. I have included installation instructions and a demonstration video for you to check out. The vehicle in the video is different, but the installation process will be the same.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Installation Instructions For The JR Products RV Cabinet Door Struts # 37270545
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Difference Between Square and Round Tube Trailer Hitches for 2010 Honda CR-V
- Q&A: ETBC7 Installation Recommendation for a 2005 Chrysler Town and Country
- Article: Trailer Hitch Receiver Sizes
- Q&A: Is Bumper Removed On Install Of Draw-Tite Trailer Hitch, # 75305, On 2007 Chrysler Town And Country
- Q&A: How To Find Lock Code for Keys To Camper
- Article: 2023 Best Gifts for Outdoor Enthusiasts
- Article: 2023 Best Gifts for Auto Enthusiasts
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: All Parts Needed to Tow With a 2007 Dodge Grand Caravan
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Trailer Towing Capacity of 2005 Chrysler Town & Country Touring Edition