How Does the Curt Trailer Hitch Install on a 1997 Toyota RAV4
Question:
my muffler is on the drivers side, there are hooks hanging down one on each side is that where the hitch gets bolted to?
asked by: Tom
Expert Reply:
The Curt trailer hitch, # C13524, will bolt to existing holes in the frame of your 1997 Toyota RAV4. The frame has existing weldnuts inside the frame that the hitch hardware will bolt to. I have included a link to the installation instructions for you.
On a vehicle that has seen at least one winter or is older, you will probably have grime and corrosion build up inside the weldnuts. I have included some links that will explain how to clean them out for hitch installation.
If you plan on towing, the correct ball mount is # 3593 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch use # 19258. For trailer wiring use # C55486.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Best Bike Racks for Electric Bikes
- Q&A: Will the Kuat NV Fit and Clear Rear Spare of a 2015 Jeep Wrangler
- Q&A: Mounting A 7-pin And 4-pin Connector To My 2018 Toyota RAV-4
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Class II vs. Class III Trailer Hitch on a 2021 Toyota Rav4
- Article: Rooftop Cargo Carriers
- Article: What Do I Need To Tow A Trailer?
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Curt Trailer Hitch Recommendation for 1996 Toyota RAV4
- Q&A: Where to Find VIN if it is Hard to Read on Trailer
- Article: My Trailer Hitch Doesn't Fit